Headphone Test: Left and Right Headphone Check
This free headphone test plays beeps in your left ear, then your right, and tells you in plain words if both sides of your headphones work and are the right way round.
- Headphones on, volume low
- Test the left ear
- Test the right ear
Do both sides of your headphones work?
Turn your volume down low first.
This sound output can't play left and right separately. Make your headphones the sound output, not a single speaker or a headset in hands-free mode.
Step 1 of 2
Your Left Ear
You will hear short beeps for about 5 seconds.
Nothing playing
Where did you hear the beeps?
Step 2 of 2
Your Right Ear
You will hear short beeps for about 5 seconds.
Where did you hear the beeps?
- Left sound
- Right sound
More Tests: Bass, Wiring and Hearing Range
Changes only these test sounds, not your Windows volume.
Each side should play only in that ear. The middle should sound like it is in the middle of your head.
A tone glides from ear to ear three times. It should move smoothly, with no jumps, gaps or crackles.
Crackles when you move your head or the cable? The cable or plug is worn.
Play the low tones one at a time. You should hear a clean, steady hum with no buzzing or rattling.
Many earbuds play little or nothing at 20 to 30 Hz. That is normal. Rattling on one side only usually means that earpiece is damaged.
The same rushing sound plays in both ears: first normal, then with one side flipped. Compare the two.
- Normal: solid and in the middle of your head.
- Flipped: wide and hard to place, with less bass.
- The other way round? One earpiece is wired backwards.
- Flipped almost silent? Both ears get the same sound (Mono audio may be on in Windows).
A tone rises from a deep hum to a high whistle over about 36 seconds. Click I Can Hear It Now when you hear it, and I Can't Hear It Anymore when it fades.
Many adults stop hearing it between 10,000 and 17,000 Hz, so a low top number is usually your ears, not your headphones. This is not a medical hearing test.
This tool runs 100% in your browser. Nothing is uploaded, saved or sent to us.
How to Test Your Headphones
- Connect your headphones and make them the sound output. In Windows 11, select the volume icon on the taskbar, then the arrow next to the volume slider, and pick your headphones. Or go to Settings > System > Sound > Choose where to play sound. In Windows 10, use Settings > System > Sound > Choose your output device.
- Turn your volume down low, and put the headphones on with L on your left ear.
- Click Start Headphone Test. Play the left sound and click where you heard it, then do the same for the right sound.
- Read the result. If something is wrong, it tells you what to do next in a few short steps.
- For a closer check, open More Tests and try Bass, Moving Sound, Wiring Check and Hearing Range.
Headphone Sound Test: What Each Check Means
This headphone test makes every sound on your computer with your browser's built-in audio. Nothing is recorded, uploaded or downloaded, and it works with wired, USB and Bluetooth headphones, earbuds and headsets, so you can use it as an earphone test too. Here is what each check listens for:
| Test | A good result | A problem sounds like |
|---|---|---|
| Left and Right | Each beep only in its own ear; middle beeps in the middle of your head | Swapped sides, both ears every time, or one side silent |
| Moving Sound | A smooth glide from ear to ear | Jumps, gaps or crackles as the tone moves |
| Bass | A clean, steady hum | Buzzing, rattling or distortion |
| Wiring Check (phase test) | Normal sounds solid and centered; Flipped sounds wide and thin | No difference, the other way round, or Flipped goes almost silent |
| Hearing Range | An unbroken tone from low to high | The tone drops out and comes back partway through |
How to Fix Headphones Only Working on One Side
- Check the balance. In Windows 11, go to Settings > System > Sound, select your headphones under Output, and set Left channel and Right channel to the same level. In Windows 10, open Settings > System > Sound > Sound Control Panel, select your headphones, and choose Properties > Levels > Balance.
- Reseat the plug. A 3.5 mm plug that isn't pushed all the way in often plays one side only. On a desktop PC, try the jack on the back instead of the front panel.
- Reconnect Bluetooth earbuds. Put both earbuds back in the case for a few seconds. If one still stays silent, go to Settings > Bluetooth & devices (Windows 10: Settings > Devices > Bluetooth & other devices), remove the earbuds and pair them again.
- Try another device. If the same side is silent on your phone too, the earpiece, cable or plug is faulty, and no setting will fix it.
How to Fix Headphones Playing the Same Sound in Both Ears
If the left and right beeps both come out of both ears, or the Flipped sound in the Wiring Check nearly disappears, your sound is being mixed to mono.
- Windows 11: Settings > Accessibility > Audio, turn Mono audio off.
- Windows 10: Settings > Ease of Access > Audio, turn Turn on mono audio off.
- Bluetooth headsets: when an app uses the headset's microphone, many headsets switch to a hands-free mode that plays mono, lower-quality sound. Close call and meeting apps, or pick a different microphone under Settings > System > Sound > Input, and test again. If Windows lists two outputs for the headset, choose the stereo one, not "Hands-Free".
Voices that fade while music still plays (a "karaoke" effect) usually mean the plug isn't fully in, or a 4-pole headset plug is in a jack that doesn't match it. Use the right adapter or the headset's own jack.
Headphones Left and Right Swapped or Off-Center
Check the L and R marks first: earbuds are easy to swap by mistake. If they're on correctly, sound software is the usual cause.
- Windows 11: in Settings > System > Sound, select your headphones, then set Audio enhancements to Off and Spatial sound to Off. Check the Left and Right channel levels on the same page.
- Windows 10: in the Sound Control Panel, open your headphones' Properties, and turn off enhancements on the Enhancements (or Advanced) tab and spatial sound on the Spatial sound tab.
- Close any equalizer or "virtual surround" app that came with your headset or PC, then test again.
If, in the Wiring Check, Normal sounds hollow and Flipped sounds centered, one earpiece is wired backwards. That is a hardware fault, and it usually happens after a cable repair.
Headphone Bass Test: Weak, Buzzing or Rattling Bass
- Weak bass on earbuds: a loose fit lets bass escape. Try a bigger or smaller ear tip until the low tones get louder.
- Nothing at 20 to 30 Hz: normal for many earbuds and small headphones. Worry only if 60 to 100 Hz is missing too.
- Buzzing or rattling on one side: lower the volume. If it still rattles at a normal level, the speaker inside that earpiece is damaged, often from being played too loud.
- Distortion at every tone: turn off audio enhancements and any equalizer app, then test again. If it only happens on this PC, see the next section.
Headphones Not Working on Your PC? Find the Cause
- The headphones: the same problem on a phone or another PC. Replace the cable if it's detachable, otherwise the headphones.
- Windows settings: other headphones show the same problem on this PC, and it changes when you change mono, balance or enhancements. Run the audio troubleshooter: in Windows 11, Settings > System > Troubleshoot > Other troubleshooters > Audio; in Windows 10, Settings > Update & Security > Troubleshoot > Additional troubleshooters > Playing Audio.
- The audio driver: the headphones work elsewhere, but on this PC they aren't detected, crackle, cut out or stopped working after an update. Right-click Start > Device Manager, expand Sound, video and game controllers, right-click your audio device and choose Update driver. If that doesn't help, choose Uninstall device and restart: Windows reinstalls the driver.
For more fixes, see how to fix sound in Windows 11 and how to fix Realtek audio driver problems. If your PC speakers are the problem rather than your headphones, use the speaker sound test.
Frequently Asked Questions
How do I test my headphones' left and right sides?
Put your headphones on with L on your left ear, turn the volume down and click Start Headphone Test above. Play the left sound and click where you heard it, then do the same for the right sound. The result tells you in plain words if each side works and is in the correct ear, and what to do if it isn't.
Why can I only hear out of one side of my headphones?
The most common causes are a plug that isn't fully inserted, the Windows balance set to one side, a Bluetooth earbud that lost its connection, or a broken wire. Check Settings > System > Sound for the Left and Right channel levels, reseat the plug, and try the headphones on another device. If one side is silent everywhere, the headphones are faulty.
Why does my Bluetooth headset sound bad when I use its microphone?
When an app uses a Bluetooth headset's microphone, many headsets switch to a hands-free mode with mono, lower-quality sound. Close call and meeting apps when you only want to listen, or pick a different microphone under Settings > System > Sound > Input. If Windows lists two outputs for the headset, choose the stereo one, not "Hands-Free".
What is the best song to test headphones?
A well-recorded song you know very well, because you can hear what has changed. Listen for clear voices, deep bass without rattling, and instruments placed left and right. But a song mixes both sides together, so it can't show swapped or silent sides as clearly as test beeps. Use the left and right test on this page first, then your song.
Is a headphone test safe for my ears and headphones?
Yes, at a sensible volume. Start with your volume low and raise it slowly: steady test tones can sound louder than music, and very high tones can be unpleasant. Don't turn bass tones up until the headphones rattle. Every test stops on its own, and the Stop Sound button or the Esc key ends it at once.
How do I do a headset mic test?
This page checks what you hear. To check your headset's microphone, use the free mic test, which shows whether your microphone picks up your voice and lets you record a short clip and play it back, all in your browser.
Sources

Before You Go: Check Your Audio Driver
Headphones crackle, cut out or stay silent only on this PC? An outdated audio or Bluetooth driver is a common cause. WinZip System Utilities Suite checks your drivers and lets you choose which updates to install.
- Scan for audio and Bluetooth driver updates
- Review drivers before updating
- Update drivers in a few clicks
Free ScanDownload Time: Under 1 minuteFor Windows 11 and 10
